HOT ! Poxi-Rock Dressing (1.5 Gallons)｜ Other Products

Poxi-Rock Dressing

Available Sizes

1.5 Gallon Unit packaged in two pails

Advantages

100% solids
"Orange Peel" texture
Good chemical resistance
VOC Compliant
High gloss finish
Good abrasion resistance

Description
POXI-ROCK DRESSING is a thixotropic 2-component, 100% solids epoxy topcoat formulated for application over most ROCK-TRED floor and wall systems. POXI-ROCK DRESSING meets all USDA/FDA guidelines for use in federally inspected facilities.
Uses
POXI-ROCK DRESSING is designed to achieve one-coat coverage over porous systems such as trowel down epoxy mortar floors and troweled cove/cant base. Due to its high viscosity it also ideal as a CMU epoxy block filler and vertical body/finish coating. POXI-ROCK DRESSING can be field thickened further by adding fumed silica and used as a 100% solids epoxy patching compound for floors, walls and ceilings. POXI-ROCK DRESSING will produce an "orange peel" finish when applied with a back roll technique. This coating is clear (slightly opaque white) and can be field pigmented with ROCK-TRED Colorants.
Typical Coverage
POXI-ROCK DRESSING is typically applied between 60-125 square feet per gallon per coat depending upon substrate and project requirements.
Physical Properties

Volume mix ratio
2 to 1 (Resin to Hardener)

Viscosity (mixed)
13,000 - 16,000 CPS Typical

Solids Content (%)
100 % (ASTM D-2697)

Hardness (ASTM D-2240)
75-80 (Shore D)

VOC
Compliant with all US Regulations

Application Temps.
60° – 85° F

Gel Time
36 - 46 minutes @ 75° F

Dry to Touch (recoat with compatible products)
3 - 5 hours @ 75° F

Through Cure
8 - 12 hours @ 75° F

Open for light traffic
24 hours @ 75° F

 
Limitations & For Best Results

Do not thin this product.
Do not apply when Humidity exceeds 70% indoors.
Do not allow to puddle during application.
Allow each coat to dry to 'tack-free' or clear prior to re-coat.

When re-coating, always apply the next coat within 24 hours of completing the previous coat.
When pigmenting this product using lighter colors application at 15 mils or in multiple coats may be required for full hide.

Product Application
Apply using brush, roller and squeegee ROCK-TRED product test data is based on environmental temperatures of 75° F (24° C). Viscosity and working time are always affected by temperatures above or below that mark. When applying product always consider the ambient, surface, and product temperature at the time and place of installation.
Color and Textures
POXI-ROCK DRESSING is manufactured in CLEAR (slightly opaque white) and can be field pigmented using ROCK-TRED colorants. Most ROCK-TRED products are available in a wide range of textures using an appropriate aggregate.
Chemical Resistance
Always refer to ROCK-TRED's chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.
Product Storage
DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50°F.
Surface Preparation
Always apply ROCK-TRED products to a clean / sound substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooring systems completely; if complete removal is not possible always perform tests to determine adhesion and compatibility to the existing flooring. Mechanical preparation by means of a shotblasting or diamond grinding machine to a minimum CSP-2 profile followed by application of an appropriate ROCK-TRED primer or base system is the best and recommended installation method for POXI-ROCK DRESSING applications. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.
Clean Up
Application tools and equipment can be cleaned with soap and water immediately after use, or with solvent once the product has begun to cure.
Disposal
Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.
Important Notice
Always read and acquaint yourself with ROCK-TRED's Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids product warranty.
Brand:Rock TredSKU:15900Tags:Clear Epoxy, Rock Tred